Were you on the lookout for additional info concerning A Step-by-Step Guide to Installing a Bathtub?
Mounting a tub isn't exactly brain surgery, however it does require strong plumbing, carpentry, and also often, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably difficult task. If the old tub is easily accessible, the job can move easily; if you have to open a wall surface to get rid of the old tub as well as place the new bath tub, the job is much harder. In either instance, the job is within a residence handyman's abilities, although you will certainly require an assistant to move out the old bathtub and also set in the brand-new one. Make sure you have qualified on your own for the work and also fit trying it. As opposed to employing a professional to take control of a halfway-completed project, it is much better to think about employing one prior to you start. Opportunities are you might need a professional plumber to make tube connections.
This write-up will aid you mount a new bathtub in your washroom if you have actually currently purchased a brand-new tub and do not need to change the setup of your previous water system pipes.
Your devices as well as product checklist need to consist of the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is separate the supply of water. After doing so, turn on the faucets to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather problematic as a result of the restricted gain access to that is usually the situation.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the faucets. Have a cloth all set for the staying water that will certainly come from the pipes. Once the supply pipelines have been removed, make use of the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the single faucets from turning throughout this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
Before carrying on to fit the new taps, contrast the pipeline connections on the old faucets to the new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic connector to stop damage to the string. One end of the adapter fits on the plastic tail of the tap and also the other end provides a connection to the current supply pipes.
If you require to fit a monobloc, after that you will need minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the installing hole in the bath/basin ensuring that the washing machines are in place in between the faucet and also the sink. Secure the faucet in position with the maker offered backnut. When the tap is securely in place, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with regular faucet ports. The former type must be linked to the faucet ends initially, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been attached.
Setting up the Tub
Making use of both wooden boards under its feet, position the tub in the needed position. The wood boards are helpful in equally spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by checking the level as well as changing the feet on the bathtub until the level reads degree.
To install faucets, fit the bottom of the furthest versatile tap port to the proper supply pipeline by making a compression sign up with; after that do the exact same for the various other faucet.
Turn on the water and also inspect all joints as well as new pipework for leaks and tighten them if necessary. Load the bath tub and likewise check the overflow outlet as well as the regular electrical outlet for leakages.
Finally, repair the bathroom paneling as described in the maker's instruction manual. Tiling and also securing around the tub must wait till the tub has been made use of at least once as this will certainly settle it right into its final placement.
Planning for the Setup
Firstly, the sustaining frame provided with the bathroom needs to be fitted (if needed) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is very important to see to it that if the faucet includes a plastic washer, it is fitted between the bath and also the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the taps system to prevent strain on the bath tub.
Fit the versatile faucet ports to the bottom of the two taps using 2 nuts and olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you use every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its final placement.
Tiling Around the Bathtub
In the area where the bath satisfies the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the fitting can move enough to fracture an inflexible seal, causing the water to penetrate the wall surface between the bathroom and the tiling, bring about complications with moisture as well as feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your components as well as installations. They are sold in tubes and cartridges, and can securing voids up to a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to constantly load the tub with water before securing, to allow for the motion experienced when the tub is in usage. The sealant can fracture fairly early if you do not consider this motion before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally conveniently available on the marketplace. It is suggested to fit the ceramic tiles using water-resistant or water resistant glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
We were made aware of that article about Installing A Bathtub from a friend on a different blog. Sharing is good. One never knows, you could be helping someone out. Many thanks for going through it.
Pro help, one ring away.